WS2812B Code Cleanup, Configuration via config.h
This commit is contained in:
parent
c573254d06
commit
5595236927
|
|
@ -13,15 +13,17 @@ platform = atmelmegaavr
|
|||
board = ATtiny3216
|
||||
framework = arduino
|
||||
|
||||
# Board Config
|
||||
board_build.f_cpu = 8000000L
|
||||
## Board Config ##
|
||||
# You might want to set f_cpu to 5MHz (5000000L) to allow operation at lower Battery Voltage - Use "Burn Fuses" after changing f_cpu
|
||||
# Be aware that some Functions (like WS2812B LED Support) will not work at 5 HMz
|
||||
board_build.f_cpu = 8000000L
|
||||
board_hardware.oscillator = internal
|
||||
board_hardware.bod = disabled
|
||||
|
||||
# Debug Port Config
|
||||
## Debug Port Config ##
|
||||
monitor_speed = 115200
|
||||
|
||||
# LMIC Config via Build Flags
|
||||
## LMIC Config via Build Flags ##
|
||||
build_flags =
|
||||
-D CFG_eu868
|
||||
-D CFG_sx1276_radio
|
||||
|
|
@ -29,7 +31,7 @@ build_flags =
|
|||
-D DISABLE_BEACONS
|
||||
-D ARDUINO_LMIC_PROJECT_CONFIG_H_SUPPRESS
|
||||
|
||||
# Programmer Config (MicroUPDI)
|
||||
## Programmer Config (MicroUPDI) ##
|
||||
upload_port = usb
|
||||
upload_protocol = xplainedmini_updi
|
||||
upload_flags =
|
||||
|
|
@ -37,5 +39,6 @@ upload_flags =
|
|||
-P$UPLOAD_PORT
|
||||
-c$UPLOAD_PROTOCOL
|
||||
|
||||
## External Libraries ##
|
||||
lib_deps =
|
||||
mcci-catena/MCCI LoRaWAN LMIC library @ ^3.3.0
|
||||
|
|
@ -4,6 +4,15 @@
|
|||
// ATTNode v3 Onboard LED is on PIN_PA7
|
||||
#define LED_PIN PIN_PA7
|
||||
|
||||
// Enable WS2812B RGB LED Support for the CO2 Addon Board
|
||||
// * First LED shows CO2-Level (green: <1000, yellow: 1000-1800, red: >=1800)
|
||||
// * Second LED shows LoRa Status (yellow: Joining, green 1s: Joined, green 100ms: Sending, blue 250ms: Received Downlink)
|
||||
// WS2812B_BRIGHT can be set to the desired brightness value for the LEDs (0=off, 255=brightest)
|
||||
// Uncomment the 3 following lines to get the default behaviour
|
||||
// #define WS2812B_PIN PIN_PC1
|
||||
// #define WS2812B_NUM 2
|
||||
// #define WS2812B_BRIGHT 32
|
||||
|
||||
// Enable Serial Debugging. Parameters for the Serial Port are 115200
|
||||
// Please be aware that the SG112A/B CO2 Sensor uses the HW-UART, so
|
||||
// Serial Debug Output is not available with this Sensor.
|
||||
|
|
|
|||
72
src/main.cpp
72
src/main.cpp
|
|
@ -31,14 +31,20 @@ void blink(uint8_t num) {
|
|||
#define BLINK_LED(COUNT)
|
||||
#endif
|
||||
|
||||
// WS2812B
|
||||
#include <tinyNeoPixel_Static.h>
|
||||
|
||||
#define WS_NUM_PIXELS 2
|
||||
|
||||
byte pixels[WS_NUM_PIXELS * 3];
|
||||
tinyNeoPixel leds = tinyNeoPixel(WS_NUM_PIXELS, PIN_PC1, NEO_GRB, pixels);
|
||||
// WS2812B RGB LEDs on the CO2 Addon Board
|
||||
// Defines the Macro Function WS2812B_SETLED so we don't need #ifdefs everywhere
|
||||
#ifdef WS2812B_PIN
|
||||
#include <tinyNeoPixel_Static.h>
|
||||
byte pixels[WS2812B_NUM * 3];
|
||||
tinyNeoPixel leds = tinyNeoPixel(WS2812B_NUM, WS2812B_PIN, NEO_GRB, pixels);
|
||||
#define WS2812B_SETLED(led,r,g,b) leds.setPixelColor(led,r,g,b); leds.show()
|
||||
#define WS2812B_BLINK(led,r,g,b,ms) leds.setPixelColor(led,r,g,b); leds.show(); delay(ms); leds.setPixelColor(led,0,0,0); leds.show()
|
||||
#else
|
||||
#define WS2812B_SETLED(led,r,g,b)
|
||||
#define WS2812B_BLINK(led,r,g,b,ms)
|
||||
#endif
|
||||
|
||||
// Create the Sensor Objects
|
||||
#if defined HAS_NO_SENSOR
|
||||
struct lora_data {
|
||||
uint8_t bat;
|
||||
|
|
@ -83,7 +89,7 @@ const lmic_pinmap lmic_pins = {
|
|||
|
||||
// List of unused Pins - will be disabled for Power Saving
|
||||
#if defined DEBUG || defined HAS_SG112A || defined HAS_MHZ19C
|
||||
const int disabledPins[] = {PIN_PB5, PIN_PB4, PIN_PB1, PIN_PB0, PIN_PC3, PIN_PC2, PIN_PC0};
|
||||
const int disabledPins[] = {PIN_PB5, PIN_PB4, PIN_PB1, PIN_PB0, PIN_PC3, PIN_PC2, PIN_PC1, PIN_PC0};
|
||||
#else
|
||||
const int disabledPins[] = {PIN_PB5, PIN_PB4, PIN_PB3, PIN_PB2, PIN_PB1, PIN_PB0, PIN_PC3, PIN_PC2, PIN_PC1, PIN_PC0};
|
||||
#endif
|
||||
|
|
@ -117,21 +123,13 @@ void onEvent(ev_t ev) {
|
|||
case EV_JOINED:
|
||||
// Disable LinkCheck
|
||||
LMIC_setLinkCheckMode(0);
|
||||
leds.setPixelColor(1, leds.Color(0,127,0));
|
||||
leds.show();
|
||||
delay(1000);
|
||||
leds.setPixelColor(1, leds.Color(0,0,0));
|
||||
leds.show();
|
||||
WS2812B_BLINK(1,0,127,0,1000);
|
||||
DEBUG_PRINTLN("OTAA Join Succeeded");
|
||||
break;
|
||||
case EV_TXCOMPLETE:
|
||||
// Check for Downlink
|
||||
DEBUG_PRINTLN("LoRa Packet Sent");
|
||||
leds.setPixelColor(1, leds.Color(0,127,0));
|
||||
leds.show();
|
||||
delay(100);
|
||||
leds.setPixelColor(1, leds.Color(0,0,0));
|
||||
leds.show();
|
||||
WS2812B_BLINK(1,0,127,0,1000);
|
||||
if ((int)LMIC.dataLen == 2) {
|
||||
// We got a Packet with the right size - lets assemble it into a uint16_t
|
||||
DEBUG_PRINTLN("Received Downlink")
|
||||
|
|
@ -140,11 +138,7 @@ void onEvent(ev_t ev) {
|
|||
DEBUG_PRINTLN(tmpslp);
|
||||
sleep_time = tmpslp;
|
||||
EEPROM.put(ADDR_SLP, tmpslp);
|
||||
leds.setPixelColor(1, leds.Color(0,0,127));
|
||||
leds.show();
|
||||
delay(250);
|
||||
leds.setPixelColor(1, leds.Color(0,0,0));
|
||||
leds.show();
|
||||
WS2812B_BLINK(1,0,0,127,250);
|
||||
}
|
||||
|
||||
// Got to sleep for specified Time
|
||||
|
|
@ -196,25 +190,24 @@ void do_send(osjob_t* j) {
|
|||
DEBUG_PRINTLN("LoRa-Packet Queued");
|
||||
LMIC_setTxData2(1, (unsigned char *)&data, sizeof(data), 0);
|
||||
|
||||
// ppm level
|
||||
#if defined WS2812B_PIN && (defined HAS_SG112A || defined HAS_MHZ19C)
|
||||
|
||||
// CO2 PPM Levels and LED Colors
|
||||
// < 1000 ppm green
|
||||
// < 1800 ppm yellow
|
||||
// > 1000 ppm red
|
||||
|
||||
if (data.ppm > 0 && data.ppm <= 1000) {
|
||||
leds.setPixelColor(0, leds.Color(0,127,0));
|
||||
leds.show();
|
||||
WS2812B_SETLED(0,0,127,0);
|
||||
} else if (data.ppm > 1000 && data.ppm <= 1800) {
|
||||
leds.setPixelColor(0, leds.Color(127,127,0));
|
||||
leds.show();
|
||||
WS2812B_SETLED(0,127,127,0);
|
||||
} else if (data.ppm > 1800) {
|
||||
leds.setPixelColor(0, leds.Color(127,0,0));
|
||||
leds.show();
|
||||
WS2812B_SETLED(0,127,0,0);
|
||||
} else {
|
||||
leds.setPixelColor(0, leds.Color(0,0,0));
|
||||
leds.show();
|
||||
WS2812B_SETLED(0,0,0,0);
|
||||
}
|
||||
#endif
|
||||
#endif // WS2812B
|
||||
#endif // #infdef HAS_NO_SENSOR
|
||||
|
||||
|
||||
}
|
||||
|
|
@ -229,13 +222,15 @@ void setup()
|
|||
Wire.begin();
|
||||
SPI.begin();
|
||||
|
||||
pinMode(PIN_PC1, OUTPUT);
|
||||
leds.setBrightness(64);
|
||||
|
||||
// Disable unused Pins (for power saving)
|
||||
// Disable unused Pins (for power saving)
|
||||
for (int i = 0; i < (sizeof(disabledPins) / sizeof(disabledPins[0])) - 1; i++)
|
||||
pinMode(disabledPins[i], INPUT_PULLUP);
|
||||
|
||||
#ifdef WS2812B_PIN
|
||||
pinMode(WS2812B_PIN, OUTPUT);
|
||||
leds.setBrightness(WS2812B_BRIGHT);
|
||||
#endif
|
||||
|
||||
// Set RTC
|
||||
while (RTC.STATUS > 0) {}
|
||||
RTC.CLKSEL = RTC_CLKSEL_INT1K_gc;
|
||||
|
|
@ -271,8 +266,7 @@ void setup()
|
|||
DEBUG_PRINTLN("Setup Finished");
|
||||
|
||||
// Schedule First Send (Triggers OTAA Join as well)
|
||||
leds.setPixelColor(1, leds.Color(127, 127, 0));
|
||||
leds.show();
|
||||
WS2812B_SETLED(1,127,127,0);
|
||||
do_send(&sendjob);
|
||||
}
|
||||
|
||||
|
|
|
|||
Loading…
Reference in a new issue